MauviStudios
Cart
Menu
  • Suzuka frame in the Dark design, angled view
  • Suzuka frame in the Dark design, close-up of the raised track
  • Suzuka, Japan: framed poster in the Dark design, front view
  • A3 and A4 frames side by side, to scale
  • Suzuka frame in the Dark design, close-up of the relief
  • Suzuka frame in the Dark design, front view

  • Drag to turn

  • Printed to order
  • Exploded view of a Mauvi Studios frame: frame, glass, spacer, 3D-printed track, poster and backing

Map data © OpenStreetMap contributors

Suzuka

Suzuka International Racing Course · Japan

₹1,799

Inclusive of all taxes

Design: Dark
Size
0/30
0/20
0/40
0/40

Personalised frames are made to order and can’t be returned.

Buy now checks out just this frame. Your cart is kept.

Buy 2, save 10% · 3 for 15% · 4 for 20%

About Suzuka

The figure of eight, with a bridge where the lap crosses itself. Esses, Spoon and the flat-out 130R, all on rolling ground.

The Suzuka track in raised relief, seen from above

Japan

The circuit

Lap length
5.807 km
Elevation change
42 m
Location
34.8443° N, 136.5330° E
Start · 15–58 m above sea level 5.807 km

Suzuka F1 track: map, location and facts

Height exaggerated so you can see it. Map data © OpenStreetMap contributors (ODbL) · elevation GEDTM30 (OpenGeoHub), CC BY 4.0.

The piece

The Suzuka frame: deep black box with glass front
The frame
The Suzuka poster printed behind the track
The print
Raised Suzuka track, close up
The track, 3D-printed
Dimensions
A4 frame 24 × 33 × 3 cm · artwork 21 × 29.7 cm
A3 frame 33 × 45 × 3 cm · artwork 29.7 × 42 cm

How it’s made

Every climb and drop, as it is

The track isn’t a printed line. It’s a small piece of terrain, built from real map and height data, and the frame is built around it.

Where the highs and lows are

The red 3D-printed track on the art print seen from a low angle, so its changing height is visible along the lap. High 465 m Low 364 m
Shown: Spa, Belgium. Heights are exaggerated so they read at this size.
Start / finishOne lapStart / finish
  • Highest point465 mprinted 10 mm
  • Lowest point364 mprinted 1.2 mm
  • Difference101 min real life, Spa

The layers

An exploded view of the frame standing upright, with the frame, glass, spacer, 3D-printed track, art print and backing board pulled apart in a row.
From the front: matte black frame, glass, a white spacer, the 3D-printed track, the circuit print and a backing. Shown: Spa, Belgium.

Up close

Close-up of the side wall of the printed track showing fine horizontal layer lines.
Layer lines of 0.08 mm. Shown: Spa, Belgium.
A cutaway of the framed print, cut across the middle: the frame wall, glass, the air gap, the printed track standing on the print, and the backing board.
Cutaway, front to back: frame, glass, air gap, track, print, backing. Shown: Spa, Belgium.

Where the data comes from

  • The trackIts centreline is traced from OpenStreetMap.
  • The heightsTaken from GEDTM30 terrain data, then exaggerated so they show on a wall. The shape of each climb and drop follows the data.
  • The printPLA at 0.08 mm layers, glued flat on the poster.

Map data © OpenStreetMap contributors (ODbL). Elevation: GEDTM30 (OpenGeoHub), CC BY 4.0.

Shipping · Returns and refunds · FAQ

Which size

More circuits

See all